How Many Downpipes Do I Need – Count by Roof Area, Free Online

What a downpipe does

A gutter collects the rain from the roof, but the gutter alone cannot get the water to the ground. That is the downpipe’s job. It carries the water from the gutter down the wall and into the drain. If a roof has too few downpipes, the gutter fills up in heavy rain and overflows, and the water runs down the wall instead of down the drain. That stains the wall, soaks the ground by the foundations, and in time can cause damp inside the house.

The rule this tool uses is simple: one downpipe for every 50 square metres of roof, with at least one downpipe on any roof. A roof of 120 square metres needs three downpipes. A roof of 40 square metres needs one. The rule is a common planning figure, and it keeps the water moving even in a heavy shower.

How to use the calculator

Measure the roof area in square metres. For a simple rectangular roof, multiply the length by the width of one slope and double it for both slopes. For a roof with several parts, measure each part on its own and add them together. Type the total area into the box and press the button, or just type and watch the result update.

The result shows the downpipe count. Below it, the detail line shows how many square metres each downpipe drains, so you can see the load on each one. The bar places your roof in one of three bands: one downpipe, two to three, or four or more. The meaning line tells you where to put them, and the next-step line reminds you to check the gutter spacing.

After the count, walk around the house and pick the corners. Put the first downpipe at the lowest corner, the second at the next lowest, and spread the rest evenly along the long runs. If a downpipe would land in front of a door or a path, move it to the next corner and check the spacing again.

Worked example: a 120 square metre roof

Take a house with a roof area of 120 square metres. Divide by 50 and you get 2.4, rounded up to three downpipes. Each downpipe drains about 40 square metres of roof, which is the number the detail line shows.

With three downpipes, the natural positions are two corners on one side and one corner on the other, or one at each of three corners if the roof has a hip. The gutter run between downpipes should stay under ten metres, so on a 24 metre gutter run the three downpipes sit about eight metres apart, which is comfortable.

Compare that with a small roof of 40 square metres, like a garage or an extension. The count is one downpipe, draining the whole 40 square metres. Put it at the lowest corner, and check that the gutter falls toward it at about one centimetre per three metres.

Who uses this calculator

Homeowners replacing gutters use it most. They measure the roof, run the numbers, and buy the right number of downpipes in the same trip as the gutter. Roofers use it to quote a job, because the downpipe count is part of the price, and a quote that misses a downpipe is a quote that loses money.

Builders use it on extensions and garages, where the roof is new and the drainage has to be planned from scratch. Surveyors use it to check whether an old house has enough downpipes, because a house with too few is a house with damp walls waiting to happen.

Honest limitations

This calculator uses roof area only. It does not know how steep the roof is, and a steep roof sheds water faster than a shallow one, so it can push more water into the gutter in a short burst. It does not know your local rainfall, and a house in a wet climate needs more drainage than the same house in a dry one.

The calculator also cannot see your house. It does not know where the doors, paths and drains are, so the positions it suggests are a starting point. Walk the site, look at where the water should go, and move the downpipes to suit the house.

Frequently asked questions

How many downpipes does a normal house need? Most houses need two or three. A roof of 100 square metres needs two, a roof of 120 needs three, and a small roof under 50 needs one.

Where should downpipes go? At the corners first, starting with the lowest ones, and then spread evenly so no stretch of gutter is longer than ten metres without a downpipe.

Can I have too many downpipes? Extra downpipes rarely hurt, but they cost money and they break up the look of the wall. One per 50 square metres is the usual balance between cost and drainage.

What size downpipe do I need? Most houses use a standard 68 millimetre round or 65 millimetre square downpipe. Bigger roofs and heavier rain areas may need a larger size, so check the gutter maker’s guide for your roof area.

También disponible en español: Cuántas bajantes necesito – Cantidad según la superficie del tejado, gratis en línea

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top