How many boards does a cold frame need?
A cold frame is a low box with a clear lid that sits over garden soil. It traps heat from the Sun, so you can start seeds weeks earlier in spring and keep salad leaves going later in autumn. The catch is the shape: the back wall is taller than the front wall, so the lid slopes and rain runs off. That slope means each wall needs a different number of boards, and guessing usually ends with a second trip to the timber yard. This tool counts the boards for you from six simple measurements, so you can buy the right amount in one trip.
The tool works with any size of frame and any size of board. It counts rows of boards up each wall, then works out how many board lengths fit along each wall. The back wall uses the back height, the front wall uses the front height, and the two ends use the average of the two heights, because the ends slope from back to front. It rounds up at every step, because you cannot buy part of a board.
How to use the tool
Measure your frame first. The length is the long side, the width is the short side, and the two heights are measured from the ground to the top edge of the wall. Then measure one board: its width (the face that shows when boards are stacked) and its length. Enter all six numbers in centimetres and press the button. The tool updates live as you type, so you can try a taller back wall or a wider board and watch the count change.
The result gives the total first, then a bar for each part: the back wall, the front wall, and the two ends together. The longest bar shows which part uses the most boards. Under that, a plain sentence tells you which part that is, and a next step reminds you to buy one spare board and screws.
Worked example
Take a frame 120 cm long and 60 cm wide, with a back wall 40 cm high and a front wall 20 cm high. Use boards 15 cm wide and 120 cm long. The back wall needs 3 rows (40 divided by 15, rounded up), and each row is one board long, so that is 3 boards. The front wall needs 2 rows, so 2 boards. Each end slopes from 40 cm down to 20 cm, an average of 30 cm, which needs 2 rows, and each row is one board long, so the two ends need 4 boards together. The total is 3 plus 2 plus 4, which is 9 boards.
Try a bigger frame: 240 cm long and 90 cm wide, with a back wall 45 cm high and a front wall 25 cm high, using boards 14 cm wide and 240 cm long, needs 12 boards: 4 for the back, 2 for the front, and 6 for the ends.
Tips for building a cold frame
Use boards at least 15 mm thick so the frame stays stiff when the soil is wet. Old scaffold boards work well and cost little. Cut the ends with the slope before you fix the walls together. Hinges on the back edge let you open the lid on warm days, which matters because a closed cold frame can overheat fast in spring sun.
Put the frame where it gets morning sun and shelter from wind. A spot against a south-facing wall is ideal in the northern hemisphere. Line the inside bottom with cardboard to slow weeds, and fill it with good compost. Start with hardy salads, such as lettuce and spinach, before you try tender plants.
Honest limits
This tool counts boards for a plain four-sided box with a sloped lid. It does not count the lid itself, the hinges, or the clear top, which are separate purchases. It assumes every board is the same width and length, and it assumes square cuts. If you cut boards at an angle for the ends, you may use slightly less wood, and if your boards are warped, you may need more. Always add one spare board. The tool also assumes the frame sits on flat ground; on a slope, measure the heights at the highest side.
Frequently asked questions
Why is the back wall taller than the front? The slope lets rain run off the lid and lets more light reach the plants. A difference of 15 to 20 cm between back and front works well for most frames.
What if my boards are a different length? Enter the real length. The tool divides each wall by the board length you give, so it works with 120 cm, 180 cm, 240 cm, or any other length.
Do I need screws for every board? Yes. Two screws per board end is a safe rule. The next step in the tool reminds you to buy screws with the boards.
Can I use the tool for a raised bed? A raised bed has four walls of the same height, so the slope logic does not apply. Set the back and front heights equal and the tool will count a level box, which works as a rough guide.
También disponible en español: Cuántas tablas para un marco frío
