How Much Guttering Do I Need – Metres by Roof Edge, Free Online

What this calculator works out

A gutter run is longer than the roof edge it hangs from. Every cut wastes a little length, every corner needs a join, and every join needs a spare piece. If you buy exactly the edge length, you will run short before the last corner. This calculator adds ten percent for cuts and joins, counts the downpipes, and counts the brackets, so one trip to the shop covers the whole job.

The maths is simple. Gutter length is the roof edge times 1.1, rounded up to the nearest tenth of a metre. Downpipes follow the rule of one every ten metres, with at least one even on a short run. Brackets sit every 0.6 metres along the whole run, because a gutter with brackets too far apart sags and holds water.

How to use the calculator

Measure the roof edge where the gutter will hang, from one end to the other, in metres. If the roof has two edges, run the calculator once for each edge, because each run needs its own downpipes. Type the length into the box and press the button, or just type and watch the result update.

The result shows the gutter metres to buy, with the ten percent waste already added. Below it, the detail line shows the downpipe count and the bracket count. The bar places your run in one of three bands: under fifteen metres is a short run, fifteen to thirty is a medium run, and over thirty is a long run that needs careful downpipe positions.

The next-step line reminds you to buy one spare gutter length and to check the fall. A gutter needs a slight slope toward the downpipe, about one centimetre of drop for every three metres of run, or the water will sit still and the gutter will overflow in heavy rain.

Worked example: a 20 metre roof edge

Take a house with a roof edge of 20 metres. Multiply by 1.1 for cuts and joins, and you get 22.0 metres of gutter to buy. That is the number the calculator shows.

Downpipes come next. Twenty metres divided by ten gives two downpipes, one at each end or one at each corner. Brackets sit every 0.6 metres, so 22 metres divided by 0.6 gives 36.7, rounded up to 37 brackets. The full shopping list is 22 metres of gutter, two downpipes and 37 brackets, plus the joins, end caps and screws the shop sells with them.

Compare that with a short run of 8 metres. The gutter comes to 8.8 metres, the downpipe count is one, and the brackets come to 15. The calculator handles both cases the same way, so a small porch and a long house wall both get a correct list.

Who uses this calculator

Homeowners replacing old gutters use it most. They measure the edge with a tape, run the numbers, and walk into the shop with a list instead of a guess. That matters because a second trip costs more in time and fuel than the spare length costs in money.

Roofers and handymen use it to quote a job fast, and DIY builders use it when they fit gutters on a shed, a garage or an extension. Estate agents and surveyors use it too, because a sagging gutter is one of the first things they notice on a house, and the fix starts with knowing how much gutter the roof needs.

Honest limitations

This calculator counts a straight run. It does not know about corners, valleys or dormers, and each corner adds a join and a little waste. If your roof edge turns a corner, measure each straight part on its own and add the results, or add one extra metre per corner to be safe.

The downpipe rule of one per ten metres is a maximum spacing, not a promise. A steep roof or a heavy rain area can push more water into the gutter than one downpipe per ten metres can clear, so in wet climates many roofers fit one per eight metres instead.

Frequently asked questions

Why add ten percent to the length? Because cuts waste length. A three-metre shop length cut to fit a 2.4 metre gap leaves a 0.6 metre offcut you cannot use, and corners need join pieces. Ten percent covers most jobs.

How many downpipes does a long house need? At least one per ten metres of gutter, placed at the corners first. A 30 metre run needs three downpipes, and a 25 metre run also needs three, because 25 divided by ten rounds up.

How far apart do brackets go? Every 0.6 metres on a normal run. Mark the first bracket 15 centimetres from the end, then every 0.6 metres after that, so the gutter cannot sag between fixings.

What fall does a gutter need? About one centimetre of drop for every three metres of run, sloping toward the downpipe. Too little fall and the water sits still. Too much fall and the gutter looks crooked from the street.

También disponible en español: Cuánto canalón necesito – Metros según el borde del tejado, gratis en línea

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top