Quick answer
A melamine splashback is easy to clean if you use the right method: warm water, a drop of mild dish soap, a soft microfibre cloth, and a dry wipe at the end. Most streaks come from the wrong cleaner, cold water, or an old cloth. Never use abrasive pads, steel wool, bleach, polish, or a steam cleaner on melamine. Abrasives leave bright patches in the surface that cannot be removed.
What melamine is (and why it marks so easily)
Melamine is a thin resin layer fused onto a board, usually MDF or particleboard. It is hard, hygienic and easy to wipe, but the protective layer is thin. Once it is scratched or chemically etched, it cannot be sanded down and refinished the way solid wood can. That is why gentle cleaning matters: the goal is to protect the finish, not scrub it.
What you need
- Two clean microfibre cloths (one damp, one dry)
- Warm water and a few drops of mild dish soap
- A soft sponge or soft brush for textured finishes
- Streak-free glass cleaner, for dark or gloss surfaces
Step 1: Dust first, then wipe
Wipe the splashback with a dry microfibre cloth first. Dust contains tiny hard particles, and dragging them across the surface under pressure works like fine sandpaper. Getting the loose dust off before any wet cleaning protects the finish.
Step 2: Wash with warm soapy water
Mix a few drops of mild dish soap into warm water. Wipe the splashback with a soft, damp microfibre cloth. For textured finishes, such as stipple or wood grain, use a soft brush to lift dirt out of the texture. Do not press hard. Let the soapy water do the work.
Step 3: Rinse and dry straight away
Wipe the surface again with a clean cloth dampened in fresh warm water, to remove all traces of soap. Then dry it at once with a clean, dry microfibre cloth or paper towel. This last step is what stops streaks. Streaks often form when the surface is cleaned with cold water, old cloths, or a cleaner that is left to dry on the surface.
How to remove streaks that are already there
If your splashback already has streak marks left by a cleaner, the fix is usually simple:
- Wipe the whole panel with warm water and a clean microfibre cloth.
- Dry it straight away with a fresh dry cloth.
- On dark or gloss surfaces, finish with a streak-free glass cleaner and a soft cloth.
Do not reach for a stronger cleaner to fix the streaks. The streaks are usually residue from the last cleaner, and adding more product makes them worse.
Grease and cooking marks
Remove fat and grease as soon as you can, ideally within 48 hours. Grease left sitting on melamine can damage the surface over time. Warm soapy water handles most cooking splashes. For stubborn greasy marks, leave a warm, damp, soapy cloth on the spot for a few minutes to loosen it, then wipe and dry.
What never to use on melamine
- Scouring pads, steel wool, abrasive powders: they scratch the surface and leave bright patches that cannot be fixed.
- Bleach and strong acids: they can etch and dull the finish.
- Polish, furniture cleaner and washing powder: they leave residues that streak and dull the shine.
- Steam cleaners: heat and steam can damage the resin layer.
- Oven cleaners and harsh solvents: far too strong for this surface.
If a mark needs something stronger than soapy water, a streak-free glass cleaner is the safe next step. For a felt-pen mark, a small amount of methylated spirits on a soft cloth is a standard fix used by kitchen makers, followed by a glass-cleaner wipe. Always test on a hidden corner first.
Daily routine that keeps it streak-free
- After cooking, wipe the splashback with a barely damp microfibre cloth.
- Dry it with a second cloth instead of letting it air-dry.
- Wash your microfibre cloths often, and never use fabric softener on them: softener leaves a waxy residue that causes streaking.
- Keep one cloth just for the splashback, so it stays clean and grit-free.
When the surface is already damaged
Bright patches from scouring, dull areas from bleach, and chips at the edges cannot be cleaned away: the resin layer itself is damaged. Small chips can sometimes be touched up with a matching repair filler from a kitchen supplier, but a badly scratched panel usually needs replacing. That is why the gentle method above is worth sticking to: prevention is the only real fix for melamine.
